氣體吸附式太干機

◆護膚品優勢 Product features

※具備有平衡一樣的的吸氣負荷和露點

1.固體吸附塔之較高與長度經實驗性可是精密模具核算，塔床水頭損失小， 保障了縮短固體干熱劑5秒的排斥時間段，能夠滿足生產設備氣的露點規范要求。

2.30％的干澀劑空間，適用來補償干澀劑的自然而然的老化，有效確保干澀。

3.小型擴散轉移器，提高認識氣體流動一致按照干躁劑層，解決溝流情況。

※降解氣量自然損耗大于14％

1.好的機筒的設計，存放100％的氣體吸附熱能量，店鋪的熱能量使用增大可復蘇的時候的可復蘇氣濕度，升高機器設備的解吸技能，會使可復蘇更根除。

2.干躁和重復選擇單向過流設計，濕暖空氣流淌干的吸收劑法定期限果很好。重復氣出口商含濕量設定在亞飽合睡眠狀態，使消音器及改裝排氣管出入口無結霜現象之慮。

3.可會按照干燥處理機的運動載荷標準的調節降解氣含量，確認降解氣團不間斷可靠，降解心理壓力低至臨界點。

※非常干燥劑施用使用期長

1.為宜的機筒大小，使氣體使用空氣非常干燥劑層的流動速度和用時堅持好的睡眠狀態，能夠充推送揮空氣非常干燥劑的性能參數。

2.合理合法的設計配備，在暖濕空氣打開機筒前，經除油正確處理當即清空暖濕空氣中內殘油物與重空氣環境有害特性，不要空氣干燥劑層受空氣污染問題。

※儀器用于了大氣高品味電動式及會自動閥和能信的全光學可和程序編寫序調控器，電腦畫質合理，會自動連續式屏幕上顯示雙塔情況，不斷循環時間是工地可編，設備添加10min。閘閥保修期將近50萬次小動作。

※鍋筒罐壁作冷熱鍍鋅防腐防銹工作，10年不生繡。

※運行較準、增強性增強、進行操作簡易，配置不須基礎上。

※Bend it out on the same has the stable pressure and dew point

1. The height and diameter adsorption tower by the experimental results calculated precisely, tower, ensure the small resistance bed compressed gas desiccant 5 seconds contact time, meet the requirements of the finished product angry dew point.

2.30% of the surplus, desiccant used to compensate for the natural aging, ensure desiccant dry.

3. Large diffuser, ensure uniform through the desiccant air layer, eliminate channel flow phenomenon.

※Bend the gas loss less than 14% renewable

1. Excellent barrel design, save 100% of the adsorption quantity of heat, storage quantity of heat is used to increase the regeneration stage again angry temperature, improve equipment desorption ability, make renewable more thoroughly.

2. Dry and regeneration of the reverse convection scheme, wet air through the dry when the adsorbent best effect. Getting angry export moisture content control in the saturated state, the muffler and exhaust passage without concentrations of condensation.

3. According to the operation of the dryer load demand adjust dosage, ensure again angry for stability, regeneration renewable air pressure low to critical.

※Bend desiccant long service life

1. The right of barrel size, make the gas through the desiccant flow velocity and time of layer be the best, give full play to the desiccant performance.

2. The reasonable system configuration, in the air into the barrel, except by the efficient before oil processing timely removal in the air in content and heavy oil pollutant, avoid desiccant layer contamination.

※The equipment adopts bend novel high quality and pneumatic valve electric and advanced and reliable full electronic programmable controller, friendly interface, automatic continuous display of the twin towers, working cycle, the programmable factory set 10 min. The valve life for 500000 times action.

※Bend the cylinder body wall be cold galvanizing antirust processing, 10 years don't rust.

※Bend action, stable performance, accurate, easy operation and installation with no need of foundation.

◆注意能力性能 Main technical parameters